A dual control PEMF machine with full body mat, packed as a rolling case. SystemA and SystemB drive two mats separately, so the body can be covered from above and below in one session.
The standard set is the control case, two mats with their own coiled cables and a bolster. Loops, paddles and extra mats are optional add-ons.
| Standard | Two mats, two cables, bolster, control case |
|---|---|
| Optional | Butterfly loop, large loop, long loop, MagFlex |
| Optional | Double beats paddles, chair cushion, square mat, PEMF mat |
Most portable units split a single output. This case carries two control systems, labelled SystemA and SystemB, and each mat has its own orange connector.
That means an operator can rest one mat under the back and lay the second over the legs, with each side set to its own intensity.
The supplier states a magnetic pulse that reaches 10 to 15cm into tissue, and a field strength that falls off more slowly than a short pulse.
The chart behind that claim is a waveform illustration, not a measured output. No tesla or gauss rating is printed on the machine or in its spec table.
Frequency runs from 1Hz to 10Hz in single steps. Intensity has ten levels from 10% to 100%, and the timer covers 1 to 20 minutes.
| Pulse frequency | 1Hz to 10Hz, 1Hz steps |
|---|---|
| Intensity | 10 steps, 10% to 100% |
| Timer | 1 to 20 minutes |
| Screen | 7 inch touch LCD |
| Control system | SystemA and SystemB |
There are no stored programmes. The operator sets frequency, intensity and time, and the mats run for the set period.
One mat goes under the body and the second goes over it, which is why the supplier calls it coverage from both sides. A single mat only works from one direction.
With the timer at 20 minutes and intensity at a comfortable level, a session covers shoulder to foot without moving the mat.
The case rolls on two wheels and pulls by a telescopic handle, and it weighs 35kg. That is light enough for a home visit but still a two-hand lift.
Suppliers position it for home care, outpatient rooms, rehabilitation centres and training schools. The mats lie on a bed, a couch or the floor.
Each mat is flexible, so it can be folded around a limb or laid flat. The two cables reach roughly the length of a treatment table.
For a shoulder or a knee, an optional loop wrapped around the joint puts the field closer than a flat mat can.
The supplier's case gallery shows the same case in bedrooms, apartments, clinics and hotel rooms. Each setup needs one socket and about two metres of floor.
Supplier copy leans on sleep, relaxation and circulation rather than on treating a named condition. Sessions are described as daily use rather than a course.
Three audiences are named: home users, people who want better sleep, and older clients who need gentle daily care. No clinical data is supplied for any of them.
The benefit list covers inflammation, stress, sleep, blood oxygenation and nerve recovery. The blood images shown beside it are illustrations, not patient results.
Treat every claim on this page as supplier material. Individual results vary, and no clinical trial is published for this model.
The supplier lists high power, solid state control and dual mat coverage as the three build points. Power output is quoted as 1000 to 3000W.
That range spans three times itself, so ask for the measured figure on your own unit before quoting it to a buyer.
Case logo, handle, internal layout, case colour, screen logo and mat colour can all be changed for a private label order.
The factory also offers training and distributor terms. Send artwork and your market, and the layout is confirmed before production.
| Output power | 1000 to 3000W, as quoted by the manufacturer |
|---|---|
| Pulse frequency | 1 to 10Hz |
| Control system | SystemA and SystemB, two independent outputs |
| Screen | 7 inch touch LCD |
| Standard applicator | Dual mat |
| Package size | 600 × 480 × 550mm |
| Weight | 35kg |
Voltage, mat dimensions and field strength are not published in the supplier sheet. Ask for them with the quotation so the page and the proforma agree.
The supplier shows an assembly line, carton racking and pallets of coiled mats ready to ship, which matters when an order is repeat business.
Q: Is this the same as a single mat PEMF device?
No. It ships with two mats and two control systems, so both mats run at once at their own settings.
Q: Can the two mats be set differently?
Yes. SystemA and SystemB are separate outputs. Frequency, intensity and time are set on the panel for the session.
Q: How many applicators come as standard?
Two mats. Loops, paddles, a chair cushion and extra mats are optional and quoted separately.
Q: What is the field strength in tesla?
The manufacturer does not publish a tesla rating for this model. Request the test report with your quotation if a buyer needs it in writing.
Q: How heavy is the case, and can one person carry it?
The packed weight is 35kg. It rolls on two wheels with a telescopic handle, and one person can lift it into a car.
Q: What is the warranty and lead time?
The factory quotes 24 months on the machine. Standard orders normally leave 3 to 7 days after payment, with logo work adding production time.
Email: hk6@huang-kai.com | WhatsApp: 86 137 5182 1215
English
中文
